Complete wood window replacement
Complete wood window replacement
I need to replace the entire wooden windows in my house due to the poor condition of the wooden trim and sill. I am looking for a replacement window manufacture that offers an entire double-hung window that has a brickmold-type trim and a sill. The house has wood siding so the window will need to a trim piece that will cover the siding where it meets the window to help make it watertight. Do any of the experts on here have a suggestion where to start looking? Thanks!
-
- Posts: 1893
- Joined: Sun Feb 22, 2009 5:52 pm
- Location: SE PA & NJ; CT
- Contact:
Re: Complete wood window replacement
Sure.
Andersen or Marvin either one will work.
What do you want the exterior to be made of ? Wood, aluminum, vinyl, or composite.
What material and finish for the interior? wood,vinyl, composite, stained, stained look, painted.
Are you planning to replace the interior casing and stools?
Andersen or Marvin either one will work.
What do you want the exterior to be made of ? Wood, aluminum, vinyl, or composite.
What material and finish for the interior? wood,vinyl, composite, stained, stained look, painted.
Are you planning to replace the interior casing and stools?
- Windows on Washington
- Posts: 4868
- Joined: Wed Apr 04, 2007 11:21 pm
- Location: DC Metropolitan Area-Maryland/Virginia/DC
- Contact:
Re: Complete wood window replacement
While a full tear out has it application value and does give you the most amount of glass back, it is not always necessary and most customers are not prepared for the added expense of new interior trim, stool, and misc carpentry work.
Exterior trim is not structural and can easily be replaced without necessitating a full tear out.
If you are going with a full tear out, you would be advised to go with a new construction window, cut back the siding, and flash the sill/jambs/head. Wood siding is notorious difficult to get sealed up properly and needs very special attention.
Exterior trim is not structural and can easily be replaced without necessitating a full tear out.
If you are going with a full tear out, you would be advised to go with a new construction window, cut back the siding, and flash the sill/jambs/head. Wood siding is notorious difficult to get sealed up properly and needs very special attention.
- HomeSealed
- Posts: 2760
- Joined: Tue Feb 16, 2010 6:14 pm
- Location: Milwaukee, Madison, Northern IL
- Contact:
Re: Complete wood window replacement
+1.Windows on Washington wrote:While a full tear out has it application value and does give you the most amount of glass back, it is not always necessary and most customers are not prepared for the added expense of new interior trim, stool, and misc carpentry work.
Exterior trim is not structural and can easily be replaced without necessitating a full tear out.
If you are going with a full tear out, you would be advised to go with a new construction window, cut back the siding, and flash the sill/jambs/head. Wood siding is notorious difficult to get sealed up properly and needs very special attention.
95% of the rot that I come across is on only the brickmold and sill nose. At worst, there may be some on the sill, but that can be spliced in. That exterior trim is not structural at all as WoW mentioned, and an insert can still be installed effectively (rotted areas can simply be cut out and patched in, or full replacement of exterior trim/brickmold if desired).
I agree on the second point as well, if you still desire to get a full tear-out, cutting back the siding would be advised in your application in order to properly flash the opening.
-
- Posts: 1893
- Joined: Sun Feb 22, 2009 5:52 pm
- Location: SE PA & NJ; CT
- Contact:
Re: Complete wood window replacement
If you do a full tear out and the existing units have brick moulding or flat casing you would not have to cut back to do a fin install.
You can do an "express install", retro fit a trip cap and back caulk to sheathing, then flashing tape the sill, install unit, cap and caulk.
You can do an "express install", retro fit a trip cap and back caulk to sheathing, then flashing tape the sill, install unit, cap and caulk.
800-399-4623